Anchor NAVI-TRAC 30 WIDE GABLE-END Bedienungsanleitung

Please read all assembly / installation instructions before the installation or removal of this product.1100 Burch Dr., Evansville, IN 47725 Ph. 812

10LAYOUT OF ALL BEAMSFIRST (2) BEAMS BUTTERFLIED SO THAT ADJACAENT BASE PLATE STAKES CAN BE USED FOR SAFE-TY GUYING. (2ND BEAM WILL BE RAISED FIRST.)

SECURING THE 1st VERTICAL BEAMERECTING THE 2nd BEAMON THE LEADING 2-PC SAFETY WEBS, WORKERS INSERT LOOSE ENDS OF UPPER SAFETY WEBS INTO THE RATCHETS O

12INSTALLING PURLINS AND RIDGE BARSCOMPLETING THE 1ST BAYIN 20’ MID BAYS, INSTALL A SUPPORT PURLIN BETWEEN THE EAVE AND THE PURLIN AT THE MID-RAFTER L

INSTALLING GUY WEBS BEFORE INSTALLING FABRICATTACH GUY WEBS TO EAVE WELDMENTS AND STAKE OUT AT 45º. SEE STAKING GUIDELINES ON PAGE 9.X-CABLED BAYSST

14INSTALLING MID PANELPULL MID PANEL UP AND OVER THROUGH CHANNELS IN RAFTER EXTRUSIONS.WHEELED PANEL GUIDERAFTERINSERT FINGERS OF WHEELED PANEL GUIDE

FABRIC TENSIONING 1. USE WEB/ RATCHETS TO SECURE CATENARY ARCHES TO UPRIGHTS, STAKE BASEPLATES BEFORE TENSIONING WEBS.ATTACH WEB/RATCHET TO TRIANGLE

16COMPLETED 30’ GABLED END NAVI-TRAC WITH FABRIC INSTALLED AND TENSIONED, GUY WEBS STAKED AND RATCHETED TIGHT. TO MEET ENGINEERING REQUIREMENTS WALL

HIP/GABLED END COMBINATION UNITSEE THE STANDARD NAVI-TRAC INSTALLATION INSTRUCTIONS FOR ASSEMBLY OF THE HIP END UNIT.EXTENSION BEAMS ARE PIVOTED IN TH

18DIAGONAL BEAM BRACE USE (OPTIONAL PURCHASE)SLIDE BOTTOM OF BEAM BRACE OVER PIN IN BASE PLATE. USE HITCH PIN TO KEEP IT IN PLACEDIAGONAL BEAM BRACE

Wall InstallationStep 1Determine which side of wall is inside and out. Ground bar pockets are on outside, Lace flap is on inside. Start by feeding t

Table of Contents Page No. Assembly Step 3 Introduction Inspect Site Frame Terminology 4 Component Illustrations

Groundbar keeper for interme-diate upright.Groundbar keeper for Corners.Prong with no hole in-serts up into upright.Cross sectional view of upright.Th

Anchor products are of superior design and operate best within the parameters of these instructions. It is imperative that the instructions be care

30’ Gabled Navi-Trac Frame TerminologyINTRODUCTION:Like the hip-end version, the gabled end NAVI-TRAC frame is made up of extruded aluminum members jo

30’ NAVI-TRAC COMPONENT ILLUSTRATIONSINSTALLATION TOOLS4

30’ NAVI-TRAC COMPONENT LISTA MINIMUM GABLED UNIT CONSISTS OF (1) KIT #1, (1) KIT #2 AND (2) EXTENSION MIDS. TO EXTEND THE LENGTH FURTHER, SIMPLY AD

I.D. 30’ GABLED END NAVI-TRACLABEL(LETTER ON DRAWING)COMPONENT DESCRIPTIONCODES(STAMPED OR TAPED)GBLKIT1GBLKIT2HIPKIT320’MIDSTR20’MIDEXT15’MIDSTR15’MI

7NAVI-TRAC Installation Safety GuidelinesYour installation techniques will evolve to fit the needs of your clients, the experience level of your crews

DIRECTIONS FOR SQUARING THE TENT1. USE A TAPE MEASURE TO MARK THE ENDS OF A LINE FOR ONE END (“A” TO “B” ABOVE) EQUAL TO THE EXACT WIDTH OF THE UNIT

STAKE-OUT DISTANCE = UPRIGHT HEIGHTWEB GUY - STAKING GUIDELINESREQUIRED DISTANCE OUT BETWEEN FRAME UPRIGHTS AND STAKE LINE IS EQUAL TO THE UPRIGHT HEI