Anchor NAVI-TRAC 50 WIDE GABLE-END Bedienungsanleitung

Please read all assembly / installation instructions before the installation or removal of this product.1100 Burch Dr., Evansville, IN 47725 Ph. 812

102-PC SAFETY WEBS: 1. LOOP (4) LOWER SAFETY WEBS OVER STAKE HEADS OF THE ADJACENT BASE PLATES, BEAMS 1 & 3 (RATCHET ENDS UP). 2. CHOOSE (4) U

SECURING THE 1st VERTICAL BEAMERECTING THE 2nd BEAMON THE LEADING 2-PC SAFETY WEBS, WORKERS INSERT LOOSE ENDS OF UPPER SAFETY WEBS INTO THE RATCHETS O

12INSTALLING PURLINS AND RIDGE BARSCOMPLETING THE 1ST BAYUSE SAME TECHNIQUE AND THE LONG LIFTING POLE WITH CRADLE TO INSTALL THE PURLINS AND RIDGE EAV

INSTALLING GUY WEBS BEFORE INSTALLING FABRICX-CABLED BAYSNAVI-TRAC UNITS 100 FT. OR MORE IN LENGTH MUST HAVE AN X-CABLED BAY NEAR THE MIDDLE OF THE U

14INSTALLING MID PANELPULL MID PANEL UP AND OVER THROUGH CHANNELS IN RAFTER EXTRUSIONS.WHEELED PANEL GUIDERAFTERINSERT FINGERS OF WHEELED PANEL GUIDE

15FABRIC TENSIONING 1. USE WEB/ RATCHETS TO SECURE CATENARY ARCHES TO UPRIGHTS, STAKE BASEPLATES BEFORE TENSIONING WEBS.ATTACH WEB/RATCHET TO TRIANGL

1650’ x 100’ GABLED END NAVI-TRACALTERNATE HIP/GABLED END COMBINATION USING KIT #3 FOR THE HIP COMPONENTS (SEE THE FOLLOWING PAGE FOR ASSEMBLY REFEREN

HIP/GABLED END COMBINATION UNITSEE THE STANDARD NAVI-TRAC INSTALLATION INSTRUCTIONS FOR ASSEMBLY OF THE HIP END UNIT.EXTENSION BEAMS ARE PIVOTED IN TH

18DIAGONAL BEAM BRACE USE (OPTIONAL PURCHASE)SLIDE BOTTOM OF BEAM BRACE OVER PIN IN BASE PLATE. USE HITCH PIN TO KEEP IT IN PLACEDIAGONAL BEAM BRACE

Wall InstallationStep 1Determine which side of wall is inside and out. Ground bar pockets are on outside, Lace flap is on inside. Start by feeding t

2 Table of Contents Page No. Assembly Step 3 Introduction Inspect Site Frame Terminology 4 Component Illustrations

20Groundbar keeper for interme-diate upright.Groundbar keeper for Corners.Prong with no hole in-serts up into upright.Cross sectional view of upright.

Anchor products are of superior design and operate best within the parameters of these instructions. It is imperative that the instructions be care

50’ Gabled Navi-Trac Frame TerminologyINTRODUCTION:Like the hip-end version, the gabled end NAVI-TRAC frame is made up of extruded aluminum members jo

50’ NAVI-TRAC COMPONENT ILLUSTRATIONSINSTALLATION TOOLS4

CONTINUED ON NEXT PAGE550’ NAVI-TRAC COMPONENT LISTA MINIMUM GABLED UNIT CONSISTS OF (1) KIT #1, (1) KIT #2 AND (2) EXTENSION MIDS. TO EXTEND THE LEN

6I.D. 50’ GABLED END NAVI-TRACLABEL(LETTER ON DRAWING)COMPONENT DESCRIPTIONCODES(STAMPED OR TAPED)GBLKIT1GBLKIT2HIPKIT320’MIDSTR20’MIDEXT15’MIDSTR15’M

7NAVI-TRAC Installation Safety GuidelinesYour installation techniques will evolve to fit the needs of your clients, the experience level of your crews

DIRECTIONS FOR SQUARING THE TENT1. USE A TAPE MEASURE TO MARK THE ENDS OF A LINE FOR ONE END (“A” TO “B” ABOVE) EQUAL TO THE EXACT WIDTH OF THE UNIT

STAKE-OUT DISTANCE = UPRIGHT HEIGHTWEB GUY - STAKING GUIDELINESREQUIRED DISTANCE OUT BETWEEN FRAME UPRIGHTS AND STAKE LINE IS EQUAL TO THE UPRIGHT HEI